Honda Civic Service Manual: Radiator Connecting Pipe Removal and Installation (R18Z1)

Honda Civic Service Manual / Powertrain / Engine / Engine Cooling / Radiator / Radiator Connecting Pipe Removal and Installation (R18Z1)

1141D2

1.	Radiator Cap

Wait until the engine is cool, then carefully remove the radiator cap.

2.	Vehicle Lift

Raise the vehicle on a lift, and make sure it is securely supported.

3.	Radiator Coolant - Replacement

Loosen the drain plug (A), and drain the coolant.

4.	Intake Air Pipe

Remove the intake air pipe.

EGR Pipe

Remove the EGR pipe (A).

6.	Thermostat Housing Peripheral Assembly

Except CVT

CVT

Disconnect the connectors (A).

Remove the harness clamps (B).

Disconnect the connector (A).

Remove the harness clamp (B).

Except M/T

M/T

Remove the harness bracket (A).

Disconnect the lower radiator hose (B), the water bypass hose (C), and the heater hose (D).

7.	Thermostat Housing

Remove the thermostat housing.

8.	Radiator Connecting Pipe

Remove the connecting pipe (A).

1.	Radiator Connecting Pipe

Install the connecting pipe (A) with new O-ring (B).

2.	Thermostat Housing

Install the thermostat housing (A), using a new gasket (B) and new O-ring (C).

3.	Thermostat Housing Peripheral Assembly

Except M/T

M/T

Connect the lower radiator hose (A), the water bypass hose (B), and the heater hose (C).

Install the harness bracket (D).

Install the harness clamp (A).

Connect the connector (B).

Except CVT

CVT

Install the harness clamps (A).

Connect the connectors (B).

EGR Pipe

22mmmmreplace

Install the EGR pipe (A) with new gaskets (B).

5.	Intake Air Pipe

Install the intake air pipe.

6.	Radiator Coolant - Replacement

Follow the chart and pour coolant into the radiator up to the base of the filler neck.

NOTE:

Use Honda Long Life Antifreeze/Coolant Type 2, and if necessary add Honda Extreme Cold Weather Antifreeze/Coolant Type 2 (concentrate). Using a non-Honda coolant can result in corrosion, causing the cooling system to malfunction or fail.

Honda Long Life Antifreeze/Coolant Type 2 is a mixture of 50 % antifreeze and 50 % water. Honda Extreme Cold Weather Antifreeze/Coolant Type 2 is a 100 % concentration coolant. Do not add water to either coolant.

If the vehicle is regularly driven in very low temperatures (below -22 °F ( -30 °C)), a 60 % concentration of coolant should be used.

Operation	Vehicle Usage (Desired Mixture)	Current Mixture	Coolant Drain	Add Amount of Honda Extreme Cold Weather Antifreeze/Coolant Type 2 (100 % concentrate)	Then add Honda Long Life Antifreeze/Coolant Type 2 (50/50)
Coolant Change	Normal Area (50/50)	50/50 60/40 unknown	Drain radiator, engine block, and reservoir	None	Top off the cooling system
	Very Cold Area (60/40)	50/50 unknown	Drain radiator, engine block, and reservoir	About 1.3 L (44 fl oz)
	Very Cold Area (60/40)	60/40	Drain radiator, engine block, and reservoir	About 1.2 L (41 fl oz)
Engine Overhaul	Normal Area (50/50)	-	-	None
Engine Overhaul	Very Cold Area (60/40)	-	-	About 1.2 L (41 fl oz)
Coolant Winterizing	Very Cold Area (60/40)	50/50	Drain about 2.0 L (68 fl oz) from radiator	About 1.2 L (41 fl oz)
Coolant Winterizing	Very Cold Area (60/40)	unknown*	Drain radiator, engine block, and reservoir	About 1.2 L (41 fl oz)

*: When you want to winterize the coolant with the minimum amount of coolant change but the current coolant concentration in the vehicle is unknown, you must drain all coolant from the cooling system.

Engine Coolant Capacities (Including the coolant reservoir capacity of 0.475 L (0.1255 US gal))

Except K24Z7 engine
	Manufacturer	Capacity
At Coolant Change	DENSO	5.59 L (1.477 US gal)
At Coolant Change	TRAD	5.50 L (1.453 US gal)
After Engine Overhaul (M/T)	DENSO	6.42 L (1.696 US gal)
After Engine Overhaul (M/T)	TRAD	6.33 L (1.672 US gal)
After Engine Overhaul (A/T)	DENSO	6.56 L (1.732 US gal)
After Engine Overhaul (A/T)	TRAD	6.47 L (1.709 US gal)
After Engine Overhaul (CVT)	DENSO	6.52 L (1.722 US gal)
After Engine Overhaul (CVT)	TRAD	6.43 L (1.699 US gal)

Engine Coolant Capacities (Including the coolant reservoir capacity of 0.475 L (0.1255 US gal))

K24Z7 engine
	Capacity
At Coolant Change	5.5 L (1.45 US gal)
After Engine Overhaul	6.7 L (1.78 US gal)

7.	Maintenance Minder Reset

After doing all procedures, select the individual maintenance item you wish to reset with the HDS..

Radiator Connecting Pipe Removal and Installation (R18A9)

1. Radiator Cap 1. Wait until the engine is cool, then carefully remove the radiator cap. ...

Radiator Removal and Installation ('12-'13: R18Z1)

114100 1. Radiator Cap 1. Wait until the engine is cool, then carefully remove the radiator cap. ...

Honda Civic Service Manual: Radiator Connecting Pipe Removal and Installation (R18Z1)

Radiator Connecting Pipe Removal and Installation (R18A9)

Radiator Removal and Installation ('12-'13: R18Z1)

See also: